Product code :
- 733-38678 N35 Light Grey
- 733-38716 N53 Blue Grey
- 733-00026 White
- 733-39141 Y14 Golden Yellow
- 976-H0177 Standard Hardener
LUXAFLOOR® FCF is a high performance, fast cure floor coating designed to get assets back into service quickly through very short cure times. LUXAFLOOR® FCF is fully cured in 1 day at 25°C. LUXAFLOOR® FCF exhibits excellent gloss and colour retention under extreme UV exposure. Combining LUXAFLOOR® FCF with LUXAFLOOR® AGGREGATES enables the fast installation of safety compliant slip resistant finishes.
LUXAFLOOR® FCF is available in White, N35 Light Grey, N53 Blue Grey & Y14 Golden Yellow.
Benefits
- Saves time - can be walked on in 2 hours, and full cure in a single day at 25°C
- Ideal for extremely limited shut down periods
Features :
- Fast cure - recoat in 2 hours at 25°c
- Fast return to service – full cure 1 day at 25°c
- Long pot life – 8 hours at 25°c
Isocyanate free
- Excellent gloss & colour retention under UV exposure, making it suitable for interior and exterior application
- Excellent system when paired with Luxafloor Express Primer
Luxafloor® Express
The Luxafloor Express range is designed to return assets to service faster. These products should be used together to meet time critical deadlines on projects
Two Pack Topcoat
• Faster return to service – full cure in one day*
• Long pot life – 8 hours*
• Use on more jobs – interior and exterior durable
Uses :
LUXAFLOOR® FCF can be used direct to correctly prepared concrete floors and with LUXAFLOOR® AGGREGATES for slip resistant finishes.
Application Methods : Brush and roller.
Surface Preparation :
New Concrete: Concrete must be at least 28 days old before coating. Remove oil, grease and other oily contaminants with Gamlen CA 1 (according to the manufacturer’s written instructions and all safety warnings). Diamond grind, blast-track or mechanically abrade concrete floors to remove laitance, curing compounds, hardeners, sealers and/or other contaminants and to provide a concrete surface profile of CSP 2-3 per ICRI 310.2R. Remove all dust and debris by vacuum cleaning. Large cracks, voids and other surface imperfections should be filled with Luxafloor® Filler or other suitable filler/surfacer as recommended by your local Protective Coatings Representative. Check moisture content of the floor prior to painting*. Prime with Luxafloor® Express Primer.
*Allow new concrete to cure a minimum of 28 days at 24°C. To minimise the risk of moisture interference, Dulux recommends the following two tests be performed prior to coating – ASTM F2659 – 10 “Standard Guide for Preliminary Evaluation of Comparative Moisture Condition of Concrete, Gypsum Cement and Other Floor Slabs and Screeds Using a Non-Destructive Electronic Moisture Meter”(moisture content not to exceed 6%) and ASTM D 4263 “Standard Test Method for Indicating Moisture in Concrete by the Plastic Sheet Method” (no visible moisture present). If there is any concern about moisture problems with the concrete slab, or for projects greater than 500m2 , at least one of the following more accurate quantitative test methods should be used - ASTM F 1869 “Standard Test Method for Measuring Moisture Vapor Emission Rate of Concrete Subfloor Using Anhydrous Calcium Chloride” (moisture vapor transmission should not exceed 1.4 kilograms (3 pounds) per 93 square metres (1,000 square feet) in a 24 hour period), ASTM F 2170 “Standard Test Method for Determining Relative Humidity in Concrete using in situ Probes” (as referred to in AS 1884-2012, relative humidity should be less than 75%) Note: The testing listed above cannot guarantee avoidance of future moisture related problems particularly with existing concrete slabs. This is especially true if the use of an under-slab moisture vapor barrier cannot be confirmed or concrete contamination from oils, chemical spills, unreacted silicates, chlorides or Alkali Silica Reaction (ASR) is suspected.
Concrete with Existing Coating: Refer to Overcoating guidance below
Application :
Mix each can thoroughly using a power mixer until the contents are uniform. Mix the contents of both pails together thoroughly with a power mixer. Box all containers before use to ensure colour consistency. Remix thoroughly before application.
Product code :
- 733-38678 N35 Light Grey
- 733-38716 N53 Blue Grey
- 733-00026 White
- 733-39141 Y14 Golden Yellow
- 976-H0177 Standard Hardener
LUXAFLOOR® FCF is a high performance, fast cure floor coating designed to get assets back into service quickly through very short cure times. LUXAFLOOR® FCF is fully cured in 1 day at 25°C. LUXAFLOOR® FCF exhibits excellent gloss and colour retention under extreme UV exposure. Combining LUXAFLOOR® FCF with LUXAFLOOR® AGGREGATES enables the fast installation of safety compliant slip resistant finishes.
LUXAFLOOR® FCF is available in White, N35 Light Grey, N53 Blue Grey & Y14 Golden Yellow.
Benefits
- Saves time - can be walked on in 2 hours, and full cure in a single day at 25°C
- Ideal for extremely limited shut down periods
Features :
- Fast cure - recoat in 2 hours at 25°c
- Fast return to service – full cure 1 day at 25°c
- Long pot life – 8 hours at 25°c
Isocyanate free
- Excellent gloss & colour retention under UV exposure, making it suitable for interior and exterior application
- Excellent system when paired with Luxafloor Express Primer
Luxafloor® Express
The Luxafloor Express range is designed to return assets to service faster. These products should be used together to meet time critical deadlines on projects
Two Pack Topcoat
• Faster return to service – full cure in one day*
• Long pot life – 8 hours*
• Use on more jobs – interior and exterior durable
Uses :
LUXAFLOOR® FCF can be used direct to correctly prepared concrete floors and with LUXAFLOOR® AGGREGATES for slip resistant finishes.
Application Methods : Brush and roller.
Surface Preparation :
New Concrete: Concrete must be at least 28 days old before coating. Remove oil, grease and other oily contaminants with Gamlen CA 1 (according to the manufacturer’s written instructions and all safety warnings). Diamond grind, blast-track or mechanically abrade concrete floors to remove laitance, curing compounds, hardeners, sealers and/or other contaminants and to provide a concrete surface profile of CSP 2-3 per ICRI 310.2R. Remove all dust and debris by vacuum cleaning. Large cracks, voids and other surface imperfections should be filled with Luxafloor® Filler or other suitable filler/surfacer as recommended by your local Protective Coatings Representative. Check moisture content of the floor prior to painting*. Prime with Luxafloor® Express Primer.
*Allow new concrete to cure a minimum of 28 days at 24°C. To minimise the risk of moisture interference, Dulux recommends the following two tests be performed prior to coating – ASTM F2659 – 10 “Standard Guide for Preliminary Evaluation of Comparative Moisture Condition of Concrete, Gypsum Cement and Other Floor Slabs and Screeds Using a Non-Destructive Electronic Moisture Meter”(moisture content not to exceed 6%) and ASTM D 4263 “Standard Test Method for Indicating Moisture in Concrete by the Plastic Sheet Method” (no visible moisture present). If there is any concern about moisture problems with the concrete slab, or for projects greater than 500m2 , at least one of the following more accurate quantitative test methods should be used - ASTM F 1869 “Standard Test Method for Measuring Moisture Vapor Emission Rate of Concrete Subfloor Using Anhydrous Calcium Chloride” (moisture vapor transmission should not exceed 1.4 kilograms (3 pounds) per 93 square metres (1,000 square feet) in a 24 hour period), ASTM F 2170 “Standard Test Method for Determining Relative Humidity in Concrete using in situ Probes” (as referred to in AS 1884-2012, relative humidity should be less than 75%) Note: The testing listed above cannot guarantee avoidance of future moisture related problems particularly with existing concrete slabs. This is especially true if the use of an under-slab moisture vapor barrier cannot be confirmed or concrete contamination from oils, chemical spills, unreacted silicates, chlorides or Alkali Silica Reaction (ASR) is suspected.
Concrete with Existing Coating: Refer to Overcoating guidance below
Application :
Mix each can thoroughly using a power mixer until the contents are uniform. Mix the contents of both pails together thoroughly with a power mixer. Box all containers before use to ensure colour consistency. Remix thoroughly before application.
Product code :
- 733-38678 N35 Light Grey
- 733-38716 N53 Blue Grey
- 733-00026 White
- 733-39141 Y14 Golden Yellow
- 976-H0177 Standard Hardener
LUXAFLOOR® FCF is a high performance, fast cure floor coating designed to get assets back into service quickly through very short cure times. LUXAFLOOR® FCF is fully cured in 1 day at 25°C. LUXAFLOOR® FCF exhibits excellent gloss and colour retention under extreme UV exposure. Combining LUXAFLOOR® FCF with LUXAFLOOR® AGGREGATES enables the fast installation of safety compliant slip resistant finishes.
LUXAFLOOR® FCF is available in White, N35 Light Grey, N53 Blue Grey & Y14 Golden Yellow.
Benefits
- Saves time - can be walked on in 2 hours, and full cure in a single day at 25°C
- Ideal for extremely limited shut down periods
Features :
- Fast cure - recoat in 2 hours at 25°c
- Fast return to service – full cure 1 day at 25°c
- Long pot life – 8 hours at 25°c
Isocyanate free
- Excellent gloss & colour retention under UV exposure, making it suitable for interior and exterior application
- Excellent system when paired with Luxafloor Express Primer
Luxafloor® Express
The Luxafloor Express range is designed to return assets to service faster. These products should be used together to meet time critical deadlines on projects
Two Pack Topcoat
• Faster return to service – full cure in one day*
• Long pot life – 8 hours*
• Use on more jobs – interior and exterior durable
Uses :
LUXAFLOOR® FCF can be used direct to correctly prepared concrete floors and with LUXAFLOOR® AGGREGATES for slip resistant finishes.
Application Methods : Brush and roller.
Surface Preparation :
New Concrete: Concrete must be at least 28 days old before coating. Remove oil, grease and other oily contaminants with Gamlen CA 1 (according to the manufacturer’s written instructions and all safety warnings). Diamond grind, blast-track or mechanically abrade concrete floors to remove laitance, curing compounds, hardeners, sealers and/or other contaminants and to provide a concrete surface profile of CSP 2-3 per ICRI 310.2R. Remove all dust and debris by vacuum cleaning. Large cracks, voids and other surface imperfections should be filled with Luxafloor® Filler or other suitable filler/surfacer as recommended by your local Protective Coatings Representative. Check moisture content of the floor prior to painting*. Prime with Luxafloor® Express Primer.
*Allow new concrete to cure a minimum of 28 days at 24°C. To minimise the risk of moisture interference, Dulux recommends the following two tests be performed prior to coating – ASTM F2659 – 10 “Standard Guide for Preliminary Evaluation of Comparative Moisture Condition of Concrete, Gypsum Cement and Other Floor Slabs and Screeds Using a Non-Destructive Electronic Moisture Meter”(moisture content not to exceed 6%) and ASTM D 4263 “Standard Test Method for Indicating Moisture in Concrete by the Plastic Sheet Method” (no visible moisture present). If there is any concern about moisture problems with the concrete slab, or for projects greater than 500m2 , at least one of the following more accurate quantitative test methods should be used - ASTM F 1869 “Standard Test Method for Measuring Moisture Vapor Emission Rate of Concrete Subfloor Using Anhydrous Calcium Chloride” (moisture vapor transmission should not exceed 1.4 kilograms (3 pounds) per 93 square metres (1,000 square feet) in a 24 hour period), ASTM F 2170 “Standard Test Method for Determining Relative Humidity in Concrete using in situ Probes” (as referred to in AS 1884-2012, relative humidity should be less than 75%) Note: The testing listed above cannot guarantee avoidance of future moisture related problems particularly with existing concrete slabs. This is especially true if the use of an under-slab moisture vapor barrier cannot be confirmed or concrete contamination from oils, chemical spills, unreacted silicates, chlorides or Alkali Silica Reaction (ASR) is suspected.
Concrete with Existing Coating: Refer to Overcoating guidance below
Application :
Mix each can thoroughly using a power mixer until the contents are uniform. Mix the contents of both pails together thoroughly with a power mixer. Box all containers before use to ensure colour consistency. Remix thoroughly before application.